Burl's Aircraft - Services
© Copyright by Burl's Aircraft. All Rights Reserved.
/
Home | Shop | Services | Parts | Tailski | 180 HP Conversion | AOSS | Helps & Hints | Contact Us
STC's, FAA-PMA's and Engineering Approvals
Aeronca Sedan STC's
• Replacement metal fuel tanks for land and sea planes with PMA
• Steel lift strut fittings with PMA
• Sea plane side steps (boot cowl mounted) with PMA
• Left-hand pilot door drawings and data only)
• Single puck Cleveland wheels and brakes (drawings and data only)
• Double puck Cleveland wheels and brakes (drawing and data only)
• Aluminum baggage door (drawings and data only)
• 180 HP Lycoming engine conversion for 15AC, S15AC
• *PMA ON ENTIRE 15AC SEDAN
• Vertical instrument panel (flight instruments are insulated from main panel)
• Steel lift strut fittings with PMA
• Sea plane side steps (boot cowl mounted) with PMA
• Left-hand pilot door drawings and data only)
• Single puck Cleveland wheels and brakes (drawings and data only)
• Double puck Cleveland wheels and brakes (drawing and data only)
• Aluminum baggage door (drawings and data only)
• 180 HP Lycoming engine conversion for 15AC, S15AC
• *PMA ON ENTIRE 15AC SEDAN
• Vertical instrument panel (flight instruments are insulated from main panel)
...........................................................................................................................................................................................
New STC and PMA Applications
• 10.35 gallon auxiliary fuel tanks (mid process now)
• Aeronca Sedan shoulder harness bracket
• Vertical Instrument Panel
• Aeronca Sedan shoulder harness bracket
• Vertical Instrument Panel
...........................................................................................................................................................................................
Engineering Design Approvals
• Alternate under-wing vent system for above-listed replacement fuel tanks with PMA
-Can be installed on current installations w/ over wing vent.
• Main beam angles upper and lower for 15AC Aeronca Sedan wing spars with PMA
• Coil wire modification for Bendix, TMC and Electrosystems magnetos (data only)
• Piper trim pulley crank pin with PMA
-Can be installed on current installations w/ over wing vent.
• Main beam angles upper and lower for 15AC Aeronca Sedan wing spars with PMA
• Coil wire modification for Bendix, TMC and Electrosystems magnetos (data only)
• Piper trim pulley crank pin with PMA
...........................................................................................................................................................................................
New PMA'd Items
• PMA'd replacement fuselage for 15AC Sedan (with or without STC'd modifications)
• PMA'd replacement wing tips
• PMA'd replacement nose bowl (for C-145)
• Firewall mount battery tray for light-weight batteries
• PMA'd replacement wing tips
• PMA'd replacement nose bowl (for C-145)
• Firewall mount battery tray for light-weight batteries
...........................................................................................................................................................................................
Replacement Parts Fabrication
Here is what we have available:
• Cessna engine mount heatshields
• Aileron/flap control locks
*Large-fits Cessna, Aeronca, Citabria, Helio
*Small-fits Piper PA-12, PA-14, PA-16, PA-18, ect.
(control locks are wool felt lined; will not destruct when frozen down and removed)
• Carb mixture and carb heat control swivels ("Bugnuts")
• Non-STC'd seaplane doors, latches, hardware, door handles-complete kits available (less window and skin)
• Enlarged side windows for 15AC Sedan
• Installation of aluminum stringers and steel tube formers for 15AC Sedan (removes all wood from fuselage)
• Solid aluminum generic interior and exterior door handles
• Master solenoid and starter solenoid combination mount with bus bar
• Water rudder pickup cable balance pulley
• Stainless steel clamps for float controls installation
• Copper bus bar material (with and without heat shrink)
• 4130 steel weld-on clamps, 1/2"-1"
• Aileron/flap control locks
*Large-fits Cessna, Aeronca, Citabria, Helio
*Small-fits Piper PA-12, PA-14, PA-16, PA-18, ect.
(control locks are wool felt lined; will not destruct when frozen down and removed)
• Carb mixture and carb heat control swivels ("Bugnuts")
• Non-STC'd seaplane doors, latches, hardware, door handles-complete kits available (less window and skin)
• Enlarged side windows for 15AC Sedan
• Installation of aluminum stringers and steel tube formers for 15AC Sedan (removes all wood from fuselage)
• Solid aluminum generic interior and exterior door handles
• Master solenoid and starter solenoid combination mount with bus bar
• Water rudder pickup cable balance pulley
• Stainless steel clamps for float controls installation
• Copper bus bar material (with and without heat shrink)
• 4130 steel weld-on clamps, 1/2"-1"
...........................................................................................................................................................................................
New Manufacture Items For 15AC Aeronca Sedans:
• Extra large cabin heat distributor box
• Header tank with over hauled Cessna fuel valve (conversion for better fuel management)
• Wing access panel covers-upper and lower
• Wing lift struts-new with certifications
• Lift tabs (stainless steel)
• New MS control yoke universal joints
• Hinge bushings and pins for tailfeathers (see parts list)
• Shoulder harness brackets
• Header tank with over hauled Cessna fuel valve (conversion for better fuel management)
• Wing access panel covers-upper and lower
• Wing lift struts-new with certifications
• Lift tabs (stainless steel)
• New MS control yoke universal joints
• Hinge bushings and pins for tailfeathers (see parts list)
• Shoulder harness brackets
, LLC